On a podium roof, water can pass through the turf and collect against a raised kerb. For rooftop sports turf drainage, draw a section from the turf edge to the receiving drain. Mark the proposed drainage level, the drain inlet and the route through or around the kerb.
If a shallow cellular layer is under consideration, use that section to decide where it ends and how it connects to the outlet. Show how the maintenance team will reach the drain once the turf is in place.

Survey the roof levels and outlets
On a ground-level field, a drainage proposal may include infiltration into suitable soil. On a roof, the waterproofing remains a boundary. The design must carry water toward the roof drainage system while preserving that boundary.
Survey the actual roof levels and drain positions before setting the playing area. Mark any raised thresholds, plant bases, kerbs and changes in level. Then draw the path from the proposed turf area to each receiving drain. A drain that looks close on plan may sit beyond a barrier or above the intended drainage level.
Keep the roof designer involved from the start. Existing waterproofing, insulation, structural capacity and access arrangements affect the proposal. An added surface should not conceal a defect that needs investigation or repair first.
Separate three decisions in rooftop sports turf drainage
The surface decision concerns the selected turf system, including its backing, infill and any shock pad. The collection decision concerns the layers below it. The discharge decision concerns the connection to the roof outlets and the route for excess water. Each part needs to work with the others.
This distinction helps avoid a common procurement gap. A turf supplier may describe water passing through the carpet, while a module supplier describes connected voids. Neither statement confirms that water can cross the edge detail and enter the existing roof drain.
For the podium example, compare the proposed drainage level with the receiving outlet level in section. Include the real interface rather than ending the drawing at the boundary of the turf. If the connection remains unresolved, the module field is not ready to be ordered.
Place a shallow module in the complete build-up
The current HCR stormwater module page identifies HCR-1000 as a factory-assembled 1000 × 1440 × 82 mm unit. Its internal structure uses HOENSOEY Cells. The 82 mm dimension describes one module, rather than the total depth of a roof sports build-up.
Allow separately for the approved protection, separation, drainage interfaces and playing-surface layers. Check the finished level at doors and adjacent walking areas. Choosing a shallow module does not remove those other requirements or establish the load capacity of the roof.
The project team must review the exact module arrangement with the surface and roof systems. Component compression figures cannot establish the capacity of the complete installation. Likewise, a product image does not prove that a layer can serve as the roof’s waterproofing protection.

Resolve the perimeter before extending the field
A continuous field can simplify the visual plan, but its perimeter deserves particular attention. A solid edging detail must not interrupt the intended water route. Similarly, a change in layer height can create a local obstruction even when adjacent modules are tightly connected.
In the hypothetical design, compare two edge conditions: a turf boundary beside an accessible drainage route, and a boundary enclosed by a raised kerb. The first may offer a clearer connection, subject to the approved detail. The second needs an explicit route through or around the enclosure. Do not assume that water will find its way out.
The broader principle is consistent with ZinCo’s guidance for usable rooftops, which discusses build-up weight and height, waterproofing protection, drainage at different levels and access to roof drains. Its sporting-surface examples concern its own systems. They do not validate another manufacturer’s assembly.
Make roof outlets accessible after handover
Rooftop sports turf drainage also needs a practical maintenance route. Show how the facilities team will reach each drain and inspect the adjoining collection area. A drain hidden below a continuous surface needs an agreed access detail, rather than a note promising that access will be possible later.
Coordinate the method with the turf and roofing teams. Identify which parts may be opened, who may open them and how they will be reinstated. Keep maintenance equipment and temporary event loads within the approved operating brief. Water routing and access should remain understandable after the installation team has left.
For this podium study, the useful sequence is clear: confirm the roof and its outlets, connect the proposed drainage level, then resolve the surface and perimeter. Review the HOENSOEY Cells component information as supporting product material. Send HOENSOEY the marked roof plan and sections to discuss a proposed module layout with the responsible project team.
